Determination of the influence of pressing parameters on the bending process of beech furniture blankets

S.A. Grytsak; S.S. Grytsak

doi:10.36930/42234904

Authors

S.A. Grytsak
S.S. Grytsak

DOI:

https://doi.org/10.36930/42234904

Keywords:

wood, bending, hydrothermal treatment, pressing, beech, regression equation, model, furniture blanks, deformability, technology

Abstract

It is substantiated that the technology of cold bending of pre-pressed blanks has a perspective. It was established that the minimum bending radius depends on the direction of pressing and the degree of pressing. It was determined that pressing in the radial and tangential directions does not give the desired effect during bending, which is evidenced by a large number of defects (respectively 47-67% and 34-61%) associated with the specific structure of the wood. In particular, during pressing, the wood cells are deformed along the pressing line, and during subsequent bending, the elongation of the wood in the peripheral part passes across the pressing line and is only partially compensated by the pressed cell walls. It was experimentally established that the results are significantly different when the workpieces are axially pressed. When the degree of pressing is increased from 15 to 25%, the number of high-quality blanks increases and amounts to 83-97%, respectively. This can be explained by the fact that during axial pressing, wood cells are deformed along the line of pressing. During subsequent bending, the elongation of the wood in the peripheral part also takes place along the line of pressing and is compensated to a much greater extent by the pressed cell walls. It was found that when the workpieces are pressed along the axis, uneven pressing along the length occurs, that is, only approximately half of the length of the workpiece is pressed. This is probably the main reason for the defect. Additional research and possibly new technological solutions are needed to solve the problem of uneven pressing during axial pressing. Prospective directions of research into bending processes of beech furniture blanks have been formed, in particular from the development of new bending technologies; optimization of pressing parameters; modeling of bending processes; study of the influence of humidity and temperature; study of the strength and durability of bent blanks.

References

Arnold, M. (2010): Effect of moisture on the bending properties of thermally modified beech and spruce. J Mater Sci 45, 669-680. https://doi.org/10.1007/s10853-009-3984-8

Bektaş, I., Güler, C., Baştürk, M.A., (2002): Principal mechanical properties of eastern beech wood (Fagus orientalis Lipsky) naturally grown in Andirin northeastern Mediterranean region of Turkey. Turkish Journal of Agriculture and Forestry 26: 147-154.

Dyachun Z.J. (2007): Konstruyuvannya mebliv: Korpusni vyroby [Furniture design: Cabinet products]: – Kyiv: Mohyla Academy House, 387 p., (in Ukrainian).

Gayda S.V. (2019). Scientific and technical basis of the use of used wood in woodworking: thesis of the Doctor of Technical Sciences in the specialty 05.23. – Lviv: UNFU. – 465 (in Ukraini-an).

Gayda S.V. (2017): Використання нечітких експертних систем для підтримки прийняття рішень в процесі сортування вживаної деревини / Vykorystannya nechitkykh ekspertnykh system dlya pidtrymky pryynyattya rishenʹ v protsesi sortuvannya vzhyvanoyi derevyny [Using fuzzy expert systems for decision support in the process of post-consumer wood sorting]. Forestry, Forest, Paper and Woodworking Industry 43:5-20 (in Ukrainian). doi: https://doi.org/10.36930/42174301

Gayda S.V. (2007): А problem of arboreal raw material is in Europe and Ukraine. Forestry, Forest, Paper and Woodworking Industry 33:55-63 (in Ukrainian).

Gayda S.V. (2009): Potential of post-consumer recovered wood and possible ways of it using in Ukraine // Forestry, Forest, Paper and Woodworking Industry 35:63-83.

Gayda, S.V. (2010). A comparative analysis of physical and mechanical parameters of various-ly designed glued boards made of post-consumer recovered wood. Forestry, Forest, Paper and Woodworking Industry 36:81-91.

Gayda S.V., Kiyko O.A. (2018): Формостійкість як критерій якості столярних плит із ВЖД / Formostiykistʹ yak kryteriy yakosti stolyarnykh plyt iz vzhyvanoyi derevyny [Shape stability as a quality criterion for PCW-made blockboards]. Scientific Works of the Forestry Academy of Sci-ences of Ukraine 17:185-192 (in Ukrainian).

Gayda S.V. (2018). Технологія МДФ-фасадів / Tekhnolohiyi MDF-Fasadiv [MDF Facade Technologies]. Forestry, Forest, Paper and Woodworking Industry 44:70-83 (in Ukrainian). doi: https://doi.org/10.36930/42184410

Gayda S.V. (2013): Технології та рекомендації до використання вживаної деревини в де-ревообробленні / Resursooshchadnі tekhnologії pereroblennya vzhivanoї derevini [Resource-saving technologies of recycling of post-consumer wood]. Scientific Bulletin of NULES of Ukraine: Tech-nology and Energy of agroindustrial complex 185(2):271-280, (in Ukrainian).

Gayda S.V. (2017): A technology and properties of furniture board (FB) made of post-consumer wood (PCW). Actual problems of forest complex 48:34-38 (in Russian).

Gayda S.V. (2015): Modeling properties of blockboards made of post-consumer wood on the basis of the finite element method. Forestry, Forest, Paper and Woodworking Industry 41:39-49.

Gayda S.V., Lesiv L.E. (2023). Mathematical model of forecasting volumes of post-consumer wood production. Forestry, Forest, Paper and Woodworking Industry, 49, 33-47. https://doi.org/10.36930/42234903] (in Ukrainian).

Gayda S.V. (2016): A investigation of form of stability of variously designed blockboards made of post-consumer wood. ProLigno 12(1):22-31.

Gayda S.V. (2016): Ekologo-tekhnologicheskiye aspekty pererabotki vtorichno ispol'zuyemoy drevesiny dlya proizvodstva pressovannykh materialov [Ecological and technological aspects of re-cycling post-consumer wood for production compacted materials]. Lesnoy vestnik / Forestry bulletin of MSFU 20(3):15-22, (in Russian).

Gayda S.V. (2016): Research on physical and mechanical characteristics of front blockboards made from post-consumer wood [Дослідження фізико-механічних характеристик фасадних сто-лярних плит із вживаної деревини]. Forestry, Forest, Paper and Woodworking Industry 42: 33-50. doi: https://doi.org/10.36930/42164206

Gayda S.V. (2016): Технологічні підходи до поверхневого очищення вживаної деревини голкофрезерним інструментом / Tekhnolohichni pidkhody do poverkhnevoho ochyshchennya vzhyvanoyi derevyny holkofrezernym instrumentom [Technological approaches to cleaning of surface of post-consumer wood of needle-milling tools]. Bulletin of KhNTUA 178:3-11, (in Ukrainian).

Gayda S.V. (2018): Дослідження та аналіз характеристик щитових конструкцій із вжи-ваної деревини / Doslidzhennya ta analiz kharakterystyk shchytovykh konstruktsiy iz vzhyvanoyi derevyny [A investigation and analysis of characteristics of solid furniture boards made of post-consumer wood]. Forestry, Forest, Paper and Woodworking Industry 44:15-25, (in Ukrainian). doi: https://doi.org/10.36930/42184402

Grytsak S.A., Gayda S.V., Kushpit A.S., Salapak L.V. (2023). Analysis of the efficiency of structural and technological solutions in the production of component units of lattice furniture products. Forestry, Forest, Paper and Woodworking Industry 49: 61-72, (in Ukrainian). doi: https://doi.org/10.36930/42234905

Gayda S.V. (2023). State and analysis of the dynamics indicators of the production volume of the woodworking and furniture industry. Forestry, Forest, Paper and Woodworking Industry 49: 4-19 (in Ukrainian). doi: https://doi.org/10.36930/42234901

Gayda S.V., Kiyko O.A. (2021): Властивості вживаної деревини як визначальний чин-ник якості меблевих виробів / Vlastyvosti vzhyvanoyi derevyny yak vyznachalʹnyy chynnyk yakosti meblevykh vyrobiv [Properties of used wood as a determining factor in the quality of furniture prod-ucts]. Scientific Works of the Forestry Academy of Sciences of Ukraine 23:152-162, (in Ukrainian). https://doi.org/10.15421/412135

Gayda S.V., Lesiv L.E. (2019): Визначення та порівняння властивостей вживаної дереви-ни основних хвойних порід / Vyznachennya ta porivnyannya vlastyvostey vzhyvanoyi derevyny os-novnykh khvoynykh porid [A determination and comparison of properties of post-consumer wood of the basic conifers]. Forestry, Forest, Paper and Woodworking Industry 45:39-46, (in Ukrainian). doi: https://doi.org/10.36930/42194506

Gayda S.V., Salapak L.V., Lesiv L.E. (2021). Vyznachennya efektyvnoho tekhnolohichnoho protsesu vyhotovlennya riznykh opornykh elementiv dlya funktsionalʹnykh ploshchyn. [Determination of an efficient technological process of manufacturing various support elements for functional sur-faces]. Forestry, Forest, Paper and Woodworking Industry 47: 58-72, (in Ukrainian). doi: https://doi.org/10.36930/42214708

Gayda S.V., Somar G.V., Sokolovskyy I.A. (2022). Хімічна природа забруднювачів як основа класифікації виробів з деревини, що підлягають утилізації / Khimichna pryroda za-brudnyuvachiv yak osnova klasyfikatsiyi vyrobiv z derevyny, shcho pidlyahayutʹ utylizatsiyi [The chemical nature of pollutants as a basis for the classification of wood products to be utilization] . Forestry, Forest, Paper and Woodworking Industry 48:13-26, (in Ukrainian). doi: https://doi.org/10.36930/42214802

Gayda S.V., Voronovich V.V. (2011): Issledovanie osobennostey gnut'ya vtorichno ispol'zue-moy drevesiny [Investigation of the features of bending of post-consumer wood]. Scientific progress – creative young: proceedings of the International Scientific Conference, Mari State University: 190-192, (in Russian).

Orikhovskyy R.Ya., Gayda S.V. (2020). The influence of different parameters of stability of production sites on the efficiency of functioning of woodworking production. Forestry, Forest, Paper and Woodworking Industry 46:49-53 (in Ukrainian). doi: https://doi.org/10.36930/42204605

Gayda S.V., Voytovych I.G. (2017): Дослідження міцності та стійкості елементів ґратча-стих меблевих виробів із вживаної деревини / Doslidzhennya mitsnosti ta stiykosti elementiv gratchastykh meblevykh vyrobiv iz vzhyvanoyi derevyny [Durability and stability of elements for beam furniture products made from post-consumer wood are investigated]. Bulletin of KhNTUA 189:62-70, (in Ukrainian).

Gayda, S., Kiyko, O. (2020): The investigation of properties of blockboards made of post-consumer wood. Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements, 63(206), 77-102. https://doi.org/10.12841/wood.1644-3985.352.10

Gayda, S., Kiyko, O. (2023): Study of Physical and Mechanical Properties of Post-Consumer Wood of Different Age. Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements, 66(212), doi: https://doi.org/10.53502/wood-177453

Gayda, S.V., Kiyko O.A. (2020): Determining the regime parameters for the surface cleaning of post-consumer wood by a needle milling tool. Eastern-European Journal of Enterprise Technologies, 5 [1 [107]], 89–97. doi: https://doi.org/10.15587/1729-4061.2020.212484.

Gayda, S.V., Kiyko O.A., Guz M.M. (2022): Research of the structure of stump and root-wood for effective use in the production of wood products. Folia Forestalia Polonica, Series A – For-estry, 64 (3):131-142, doi: https://doi.org/10.2478/ffp-2022-0011

Grytsak S.A., Gayda S.V. (2020): Порівняльний аналіз фізико-механічних характерис-тик гнутих елементів із різних порід дерев / Porivnyalʹnyy analiz fizyko-mekhanichnykh kharakterystyk hnutykh elementiv iz riznykh porid derev [Comparative analysis of physical and mechanical characteristics of bent elements from different tree species]. Forestry, Forest, Paper and Woodworking Industry 46:16-27, (in Ukrainian). doi: https://doi.org/10.36930/42204602

Kiyko O.A. (2010): Statystychni metody pidvyshchennya yakosti produktsiyi derevoobroblennya [Statistical methods of improving the quality of woodworking products]. – Lviv: Panorama. – 228 p., (in Ukrainian).

Lesiv L.E. (2022): Дослідження характеристик комбінованих столярних плит із вжива-ної де-ревини / Doslidzhennya kharakterystyk kombinovanykh stolyarnykh plyt iz vzhyvanoyi derevyny [Study of the characteristics of combined of blockboards made of post-consumer wood]. Forestry, Forest, Paper and Woodworking Industry 48:69-86, (in Ukrainian). doi: https://doi.org/10.36930/42214806

Skarvelis M., Mantanis G.I. (2013): Physical and mechanical properties of beech wood harvested in the Greek public forests. Wood Research (Bratislava), Vol. 58, No. 1, 123-129.

Varga, D., van der Zee, M.E. (2008): Influence of steaming on selected wood properties of four hardwood species . Holz Roh Werkst 66, 11-18. https://doi.org/10.1007/s00107-007-0205-5

Vintoniv I.S., Sopushynskyy I.M., Teishinger A. (2007): Derevynoznavstvo [Wood-science]. – Lviv: Apriori. – 312 p., (in Ukrainian).

Voytovych I.G. (2010): Osnovi tekhnologії virobіv z derevini [The basic technology of wood]. – Textbook. –Lviv: Kraine andeljat. – 304 p. (in Ukrainian).