Study of the influence of breed and grinding modes on the specific productivity of grinding skin

S.V. Gayda; I.V. Petryshak; G.V. Somar

doi:10.36930/42204601

Authors

S.V. Gayda
I.V. Petryshak
G.V. Somar

DOI:

https://doi.org/10.36930/42204601

Keywords:

technology, roughness, grinding, oak, spruce, cutting speed, pressing force, feed speed, specific productivity of grinding skin

Abstract

It is investigated that wood species influences the indicators of grinding process: surface roughness, specific skin productivity, skin efficiency, cutting force, which in general also depend on the speed of cutting and feeding, pressing force, abrasive grain size. It is confirmed that the specific productivity of the skin during the grinding of spruce is higher by 14.25-18.77% than when processing oak wood. It is established that with the increase of the feed rate the height of the irregularities increases, as the thickness of the chips, which is removed by one active grain, increases. This is significant for tree species with lower density and hardness. It is investigated that with the increase of the feed rate during the treatment of the oak wood surface the specific productivity of the sanding skin increases by 24.62-31.40%, and in spruce – by 23.14-24.02%. It is established that with the increase of grinding time during the treatment of the oak wood surface the specific productivity of the skin decreases by 162.68-190.40%. and in spruce – by 114.29-176.09%. The specific productivity of the skin during the grinding of spruce is higher by 18.90-22.47% than when processing oak wood. It is confirmed that with increasing grain size of the abrasive, the purity of the polished surface deteriorates, ie the value of the roughness of the treated surface is directly proportional to the grain size of the abrasive. It was found that the presence of oils in spruce causes rapid salinization of the skin, ie to reduce its efficiency. It was found that the sequence of use of the positions of the skins help to increase the productivity of grinding and obtain the purity of the desired class. To carry out effective grinding to obtain a quality surface, the following input processing values are recommended: cutting speed 20-30 m / s; feed speed 6-8 m / min; specific clamping force 2.2-4.4 kPa; grain size of skins: P180-P150; P120-P100; P90-P60.

References

Bagriychuk V.A. (1983). Optimizatsiya protsessa kalibrovaniya plitnykh drevesnykh materialov zhestkim abrazivnym instrumentom [Optimization of the process of calibration of board wood materials with a rigid abrasive tool]. Abstract of PhD.. Lviv, 25 p. (in Ukrainian)

Berenis A.A. (1976). Nekotoryye voprosy kinetiki shlifovaniya krugaykh detaley na lentochnom bestsentrovom stanke [Some questions of the kinetics of grinding circles on a beltless centerless machine]. Forestry, Forest, Paper and Woodworking Industry 6: 23-29 (in Russian)

Berenis A.A. (1977). Issledovanye protsessa bestsentrovoho shlyfovanyya kruhlykh derevyannykh detaley. [Study of the process of centerless grinding of round wooden parts]. Abstract PhD. – Lviv. – 25 p. (in Russian)

Bugaenko Ya.P. (2010). Do pytannya profilʹnoho shlifuvannya derevyny [On the issue of profile sanding of wood]. Forestry, Forest, Paper and Woodworking Industry 36:100-102 (in Ukrainian).

Buglay B.M. (1957). Issledovanye y normalyzatsyya chystoty poverkhnosty drevesyny [Investigation and normalization of wood surface cleanliness]. Abstract of the doctor of technical sciences. Moscow, 36 p. (in Russian)

Castalian A.F. (1952). Shlifovaniye drevesiny [Sanding wood]. Abstract of PhD. Moscow, 21 p. (in Russian)

Gayda S.V. (1998). Основи створення гнучких автоматизованих виробництв [Basics of creating flexible automated production]. – Lviv. – 149 p. (in Ukrainian).

Gayda S.V. (1999). Проблеми та перспективи роботизації меблевої промисловості [Problems and prospects of robotics in the furniture industry]. Scientific Bulletin of UNFU 9.5:192-195. (in Ukrainian).

Gayda S.V. (2000). Визначення стійкості та міцності вертикальних стінок корпусних меблевих ви-робів [Determination of stability and strength of vertical walls of case furniture products]. Scientific Bulletin of UNFU 10.3:127-129. (in Ukrainian).

Gayda S.V. (2000). Матеріали для виготовлення виробів з деревини / Materials for the Productsion of wood Productss. Lviv: BMC. – 160 p. (in Ukrainian).

Gayda S.V. (2000). Особливості розрахунку корпусних виробів на міцність [Peculiarities of strength calculation of hull products]. Scientific Bulletin of UNFU 10.2:150-154. (in Ukrainian).

Gayda S.V. (2002). Особливості та перспективи роботизації меблевої промисловості України [Peculiarities and prospects of robotization of the furniture industry of Ukraine]. Scientific Bulletin of UNFU 12.5:38-40. (in Ukrainian).

Gayda S.V. (2003). Гнучкі виробничі модулі для виготовлення ґратчастих меблевих виробів [Flexible production modules for the production of lattice furniture products]. Scientific Bulletin of UNFU 13.2:120-122. (in Ukrainian).

Gayda S.V. (2004). Інтегровані технології меблевого виробництва [Integrated technologies of furni-ture production]. Scientific Bulletin of UNFU 14.4:118-121. (in Ukrainian).

Gayda S.V. (2007). Дослідження концентрації операцій у сучасному меблевому виробництві / Doslidzhennya kontsentratsiyi operatsiy u suchasnomu meblevomu vyrobnytstvi [Research of concentration of operations is in modern furniture Productsion]. Forestry, Forest, Paper and Woodworking Industry 33:73-79 (in Ukrainian).

Gayda S.V. (2007). Проблема деревної сировини у Європі та Україні / Problema derevnoyi syrovyny u Yevropi ta Ukrayini [А problem of arboreal raw material is in Europe and Ukraine]. Forestry, Forest, Paper and Woodworking Industry 33:55-63 (in Ukrainian).

Gayda S.V. (2011). Вживана деревина – додатковий ресурс сировини / Vzhyvana derevyna – dodat-kovyy resurs syrovyny [Recovered wood is additional resource of raw material]. Forestry, Forest, Paper and Woodworking Industry 37(1). 238-244 (in Ukrainian).

Gayda S.V. (2013). The technological solutions for recycling of post-consumer wood. Proceedings of I International Interdisciplinary Scientific Conference Formation of stable outlook as the basis of sustainable development (Ukraine, Lviv, 14-16 March 2013) UNFU: Lviv, 5-11.

Gayda S.V. (2013). Основи формування класифікатора вторинних деревинних ресурсів / Osnovy formuvannya klasyfikatora vtorynnykh derevynnykh resursiv [Bases of secondary wood resources classifier for-mation]. Scientific Works of the Forestry Academy of Sciences of Ukraine 11:208-215 (in Ukrainian).

Gayda S.V. (2013). Розроблення технології виробництва паливних гранул на основі енергетичного потенціалу вживаної деревини [Development of technology for the production of fuel pellets based on the energy potential of used wood]. Scientific Bulletin of UNFU 23.14:83-93. (in Ukrainian).

Gayda S.V. (2013): Tekhnologії ta rekomendatsії do vikoristannya vzhivanoї derevini v derevoobroblennі [Technologies and recommendations on the utilization of post-consumer wood in woodworking industry]. Forestry, Forest, Paper and Woodworking Industry 39(1):48-67, (in Ukrainian).

Gayda S.V. (2014). Sposoby podgotovki k pererabotke vtorichno ispol'zuyemoy drevesiny iglofrezernymi i shchotochnymi stankami [Preparation methods for processing of post-consumer wood (PCW) needle-milling and brushing machines]. Actual problems of forest complex 40:65-69 (in Russian).

Gayda S.V. (2015). Investigation of physical and mechanical properties of post-consumer wood. Actual problems of forest complex 43:175-179, (in Russian).

Gayda S.V. (2015). Tekhnologії і fіziko-mekhanіchnі vlastivostі stolyarnikh plit іz vzhivanoї derevini [Technology and physical and mechanical properties blockboard made of post-consumer wood]. Technical ser-vice of agriculture, forestry and transport systems 3(1).145-152 (in Ukrainian).

Gayda S.V. (2016). Ekologo-tekhnologicheskiye aspekty pererabotki vtorichno ispol'zuyemoy drevesiny dlya proizvodstva pressovannykh materialov [Ecological and technological aspects of recycling post-consumer wood for production compacted materials]. Lesnoy vestnik / Forestry bulletin of MSFU 20(3).15-22 (in Rus-sian).

Gayda S.V. (2016). Formoustoychivost' stolyarnykh plit iz vtorichno ispol'zuemoy drevesin [A form of stability of blockboards made of post-consumer wood]. Actual problems of forest complex 46:148-153, (in Russian).

Gayda S.V. (2016). Технологічні підходи до поверхневого очищення вживаної деревини голкофре-зерним інструментом / Tekhnolohichni pidkhody do poverkhnevoho ochyshchennya vzhyvanoyi derevyny holkofrezernym instrumentom [Technological approaches to cleaning of surface of post-consumer wood of needle-milling tools]. Bulletin of KhNTUA 178:3-11 (in Ukrainian).

Gayda S.V. (2017). Tekhnologiya i svoystva mebel'nogo shchita iz vtorichno ispol'zuemoy drevesiny [A technology and properties of furniture board made of post-consumer wood]. Actual problems of forest complex 48:34-38, (in Russian).

Gayda S.V. (2017). Використання нечітких експертних систем для підтримки прийняття рішень в процесі сортування вживаної деревини / Vykorystannya nechitkykh ekspertnykh system dlya pidtrymky pryynyattya rishenʹ v protsesi sortuvannya vzhyvanoyi derevyny [Using fuzzy expert systems for decision sup-port in the process of post-consumer wood sorting]. Forestry, Forest, Paper and Woodworking Industry 43:5-20 (in Ukrainian). doi: https://doi.org/10.36930/42174301

Gayda S.V. (2017). Комплексні дослідження зміни пружних властивостей вживаної деревини ялиці з віком / Kompleksni doslidzhennya zminy pruzhnykh vlastyvostey vzhyvanoyi derevyny yalytsi z vikom [The complex studies on the change of elastic properties of post-consumer fir wood with age]. Forestry, Forest, Paper and Woodworking Industry 43:58-72 (in Ukrainian). doi: https://doi.org/10.36930/42174308

Gayda S.V. (2018). Strength of combined blockboard made of post-consumer wood (PCW). Bulletin of KhNTUA 197:3-9, (in Ukrainian).

Gayda S.V. (2018). Дослідження та аналіз характеристик щитових конструкцій із вживаної дере-вини / Doslidzhennya ta analiz kharakterystyk shchytovykh konstruktsiy iz vzhyvanoyi derevyny [A investigation and analysis of characteristics of solid furniture boards made of post-consumer wood]. Forestry, Forest, Paper and Woodworking Industry 44:14-24 (in Ukrainian). doi: https://doi.org/10.36930/42184402

Gayda S.V. (2018). Технологія МДФ-фасадів / Tekhnolohiyi MDF-Fasadiv [MDF Facade Technologies]. Forestry, Forest, Paper and Woodworking Industry 44:70-83 (in Ukrainian). doi: https://doi.org/10.36930/42184410

Gayda S.V. (2019). Scientific and technical basis of the use of used wood in woodworking: thesis of the Doctor of Technical Sciences in the specialty 05.23. – Lviv: UNFU. – 465 (in Ukrainian).

Gayda S.V. (2019). Визначення та порівняння властивостей вживаної деревини основних хвой-них порід / Vyznachennya ta porivnyannya vlastyvostey vzhyvanoyi derevyny osnovnykh khvoynykh porid [A determination and comparison of properties of post-consumer wood of the basic conifers]. Forestry, Forest, Paper and Woodworking Industry 45:38-49 (in Ukrainian). doi: https://doi.org/10.36930/42194506

Gayda S.V., Bilyy Ya.M. (2019). Дослідження технологічних процесів виготовлення ліжок двос-пальних різних конструкцій / Doslidzhennya tekhnolohichnykh protsesiv vyhotovlennya lizhok dvospalʹnykh riznykh konstruktsiy [A investigation of technological processes of making beds of double different designs]. Forestry, Forest, Paper and Woodworking Industry 45:21-31 (in Ukrainian). doi: https://doi.org/10.36930/42194504

Gayda S.V., Kiyko O.A. (2013). Технология очистки вторично используемой древесины иглофре-зерными станками [The technology of cleaning recycled wood with needle milling machines] // Actual prob-lems and prospects of the development of LPK: materials II NTK., September 9-11, 2013 – Kostroma. – P. 36-39. (in Russian).

Gayda S.V., Kiyko O.A. (2018). Shape stability as a quality criterion for PCW-made blockboards. Pro-ceedings of the Forestry Academy of Sciences of Ukraine, 17, 185-192. https://doi.org/10.15421/411834 (in Ukrainian)

Gayda S.V., Kiyko O.A. (2020). Determining the regime parameters for the surface cleaning of post-consumer wood by a needle milling tool. Eastern-European Journal of Enterprise Technologies, 5 (1 (107)), 89–97. doi: https://doi.org/10.15587/1729-4061.2020.212484.

Gayda S.V., Kiyko O.A. (2020). The investigation of properties of blockboards made of post-consumer wood. Poznan : Drewno, 63 (206), 77-102. doi: https://doi.org/10.12841/wood.1644-3985.352.10.

Gayda S.V., Kshyvetskyy B.Ya. (1999). Техніко-економічні характеристики деревообробної фабри-ки майбутнього [Technical and economic characteristics of the woodworking factory of the future]. Scientific Bulletin of UNFU 9.3:83-85. (in Ukrainian).

Gayda S.V., Lesiv L.E. (2019). Визначення та порівняння властивостей вживаної деревини ос-новних хвойних порід / Vyznachennya ta porivnyannya vlastyvostey vzhyvanoyi derevyny osnovnykh khvoynykh porid [A determination and comparison of properties of post-consumer wood of the basic conifers]. Forestry, Forest, Paper and Woodworking Industry 45:39-46 (in Ukrainian). doi: https://doi.org/10.36930/42194506

Gayda S.V., Maksimiv V.M., Kiyko O.A., Ferenc O.B. (2013). Залишки деревини та деревина після споживання. Класифікація. Терміни та визначення [Wood residues and post-consumer wood. Classification. Terms and definitions] / Agreement No. 08.24-11-1: draft international standard ISO. – Lviv: NLTU of Ukraine – 53 p. (in Ukrainian).

Gayda S.V., Maksymiv V.M. (2007). Аналіз, особливості, проблеми та досвід використання до-даткових ресурсів сировини – відходів та вживаної деревини / Analiz, osoblyvosti, problemy ta dosvid vykorystannya dodatkovykh resursiv syrovyny – vidkhodiv ta vzhyvanoyi derevyny [Analysis, features, problems and experience of the use of additional resources of raw material – wastes and of used wood]. Forestry, Forest, Paper and Woodworking Industry 33:63-73 (in Ukrainian).

Gayda S.V., Nikityuk L.O. (1998). До питання застосування екстрагованої деревини для плитного виробництв [On the issue of using extracted wood for slab production]. Scientific Bulletin of UNFU 8:75-77. (in Ukrainian).

Gayda S.V., Voronovich V.V. (2011). Investigation of the features of bending of post-consumer wood // Proceedings of the Conference, Mari State University. – 190-192 (in Russian).

Kiyko O.A. (1994). Novyy instrument dlya chystovoho shlifuvannya derevyny [A new tool for fine sanding of wood] // Scientific Bulletin of UNFU 1:91-94 (in Ukrainian)

Kiyko O.A. (1995). Vplyv shvydkosti rizannya, shvydkosti podachi ta velychyny prytyskannya na sylovi pokaznyky protsesu shlifuvannya kombinovanymy zhorstko-pruzhnymy abrazyvnymy kruhamy [Influence of cutting speed, feed rate and pressure on the force indicators of the grinding process by combined rigid-elastic abrasive wheels] // Scientific Bulletin of UNFU 3(1).143-145 (in Ukrainian)

Kiyko O.A. (1999). Deyaki konstruktyvni osoblyvosti elastychnykh abrazyvnykh instrumentiv dlya shlifuvannya derevyny [Some design features of elastic abrasive tools for sanding wood] // Scientific Bulletin of UNFU 9(5).165-168 (in Ukrainian)

Petryshak I.V. (2003). Doslidzhennya rezhymnykh parametriv protsesu shlifuvannya derevyny buka zhorstko-pruzhnymy abrazyvnymy instrumentamy [Investigation of regime parameters of beech wood grinding process by rigid-elastic abrasive tools] // Scientific Bulletin of UNFU 13(2).133-136 (in Ukrainian)

Petryshak I.V. (2003). Vyznachennya konstruktyvnykh parametriv zhorstko-pruzhnoho abrazyvnoho instrumenta [Determination of design parameters of rigid-elastic abrasive tool] // Scientific Bulletin of UNFU 13(1).137-142 (in Ukrainian)

Petryshak I.V. (2006). Obgruntuvannya strukturnykh parametriv zhorstkopruzhnoho abrazyvnoho instrumenta [Substantiation of structural parameters of rigid abrasive tool] // Nauk. Bulletin: Coll. scientific and technical work. – Lviv: NLTU of Ukraine. – 2006, issue. 16.3. – P. 70-75.

Popov Yu.P. (1964). . Issledovanye rabotosposobnosty shlyfovalʹnoy shkurky [Study of the efficiency of the grinding skin]. Abstract of PhD. Moscow, 23 p. (in Russian)

Pyzhuryn A.A. (1984). Issledovanye protsessov derevoobrabotky [Research of woodworking processes]. Moscow: Forest Industry, 232 p. (in Russian)

Rudakov B.N. (1940). Issledovanyya kachestva shlyfovannoy poverkhnosty drevesyny [Research of quality of the polished surface of wood]. Abstract of PhD. Moscow, 20 p. (in Russian)

Zayatz I.M. (2001). Obrobka derevini í derevinnikh materíalív abrazivami [Abrasive treatment of wood and wood materials]. Lviv: Atlas. 219 p. (in Ukrainian)