Analysis of the efficiency of structural and technological solutions in the production of component units of lattice furniture products

S.A. Grytsak; S.V. Gayda; A.S. Kushpit; L.V. Salapak

doi:10.36930/42234905

Authors

S.A. Grytsak
S.V. Gayda
A.S. Kushpit
L.V. Salapak

DOI:

https://doi.org/10.36930/42234905

Keywords:

furniture products, chair, technologies, wood products, technological processes, comparative analysis, gluing, economic efficiency, furniture board

Abstract

The existing types of backs of carpentry chairs, which are part of a kitchen set of furniture, which are constructed from elements of hard wood species, in particular oak, and the technological processes of their manufacture have been analyzed. The technologies and production processes accompanying the creation of the backs of carpentry chairs are analyzed and described in detail. The methodology of research and comparison of technological processes of manufacturing the backs of carpentry chairs with structural features are substantiated. The necessary materials for two types of manufacturing backs of carpentry chairs from oak wood from natural wood were selected and calculated. The necessary basic equipment was selected and calculated according to the developed manufacturing technologies for two options for the manufacture of chair backs. The necessary technological routes for each variant of manufacturing the backs of carpentry chairs were selected, developed and calculated. Two shop plans are proposed according to the developed technologies for manufacturing the backs of carpentry chairs. A comparison of the amount of equipment loading of each variant of manufacturing the backs of carpentry chairs was carried out. The results of the preliminary analysis based on the data of three indicators (cost and capacity of the equipment, number of employees) gave the right to recommend the second option for the manufacture of the backs of carpentry chairs, which are included in the set of kitchen furniture, which is constructed from prepared elements of solid species of wood, in particular oak from natural wood, where the cost of equipment is the lowest and amounts to UAH 827.65 thousand, the number of employees is 8, the total power is 15.27 kW. On the other hand, the cost of materials for the first option is much higher than in the second. Economic calculations proved and calculated that the least expensive for the implementation of the annual program in the amount of 30,000 backs of carpentry chairs, which are included in the set of kitchen furniture, which is constructed from prepared elements from hard species of wood, in particular, oak from natural wood, is the second option, where the investments amounted to UAH 14,252.98 thousand, which is 20% less than in the first option.

References

Dyachun Z.J. (2007): Konstruyuvannya mebliv: Gratchasti ta mʺyaki vyroby [Furniture design: lattice and soft products]: – Kyiv: Mohyla Academy House, 482 p., (in Ukrainian).

Gayda S.V. (2019). Scientific and technical basis of the use of used wood in woodworking: thesis of the Doctor of Technical Sciences in the specialty 05.23. – Lviv: UNFU. – 465 (in Ukraini-an).

Gayda S.V. (2017): Використання нечітких експертних систем для підтримки прийняття рішень в процесі сортування вживаної деревини / Vykorystannya nechitkykh ekspertnykh system dlya pidtrymky pryynyattya rishenʹ v protsesi sortuvannya vzhyvanoyi derevyny [Using fuzzy expert systems for decision support in the process of post-consumer wood sorting]. Forestry, Forest, Paper and Woodworking Industry 43:5-20 (in Ukrainian). doi: https://doi.org/10.36930/42174301

Gayda S.V. (2009): Potential of post-consumer recovered wood and possible ways of it using in Ukraine // Forestry, Forest, Paper and Woodworking Industry 35:63-83.

Gayda, S.V. (2010). A comparative analysis of physical and mechanical parameters of vari-ously designed glued boards made of post-consumer recovered wood. Forestry, Forest, Paper and Woodworking Industry 36:81-91.

Gayda S.V. (2013): Ресурсоощадні технології перероблення вживаної деревини / Resur-sooshchadnі tekhnologії pereroblennya vzhivanoї derevini [Resource-saving technologies of recy-cling of post-consumer wood]. Scientific Bulletin of NULES of Ukraine: Technology and Energy of agroindustrial complex 185(2):271-280, (in Ukrainian).

Gayda S.V., Kiyko O.A. (2018): Формостійкість як критерій якості столярних плит із ВЖД / Formostiykistʹ yak kryteriy yakosti stolyarnykh plyt iz vzhyvanoyi derevyny [Shape stability as a quality criterion for PCW-made blockboards]. Scientific Works of the Forestry Academy of Sci-ences of Ukraine 17:185-192 (in Ukrainian).

Gayda S.V. (2014): Techniques for recycled of post-consumer wood in the production of quality particleboard. Forestry, Forest, Paper and Woodworking Industry 40:41-51.

Gayda S.V. (2018). Технологія МДФ-фасадів / Tekhnolohiyi MDF-Fasadiv [MDF Facade Technologies]. Forestry, Forest, Paper and Woodworking Industry 44:70-83 (in Ukrainian). doi: https://doi.org/10.36930/42184410

Gayda S.V. (2015): Modeling properties of blockboards made of post-consumer wood on the basis of the finite element method. Forestry, Forest, Paper and Woodworking Industry 41:39-49.

Gayda S.V. (2017): A technology and properties of furniture board (FB) made of post-consumer wood (PCW). Actual problems of forest complex 48:34-38 (in Russian).

Gayda S.V. (2011): The investigation of physical and mechanical properties of wood parti-cleboards made from post-consumer wood. Forestry, Forest, Paper and Woodworking Industry 37(2):95-110.

Gayda S.V. (2016): A investigation of form of stability of variously designed blockboards made of post-consumer wood. ProLigno 12(1):22-31.

Gayda S.V. (2016): Research on physical and mechanical characteristics of front blockboards made from post-consumer wood [Дослідження фізико-механічних характеристик фасадних столярних плит із вживаної деревини]. Forestry, Forest, Paper and Woodworking Industry 42: 33-50. doi: https://doi.org/10.36930/42164206

Gayda S.V. (2016): Технологічні підходи до поверхневого очищення вживаної деревини голкофрезерним інструментом / Tekhnolohichni pidkhody do poverkhnevoho ochyshchennya vzhyvanoyi derevyny holkofrezernym instrumentom [Technological approaches to cleaning of surface of post-consumer wood of needle-milling tools]. Bulletin of KhNTUA 178:3-11, (in Ukrainian).

Gayda S.V. (2016): Эколого-технологические аспекты переработки вторично исполь-зуемой древесины для производства прессованных материалов. Ekologo-tekhnologicheskiye aspekty pererabotki vtorichno ispol’zuyemoy drevesiny dlya proizvodstva pressovannykh materialov [Ecological and technological aspects of recycling post-consumer wood for production compacted materials]. Lesnoy vestnik / Forestry bulletin of MSFU 20(3):15-22, (in Russian).

Gayda S.V. (2018): Mitsnist kombinovanykh stolyarnykh plyt iz vzhyvanoyi derevyny [Strength of combined blockboard made of post-consumer wood (PCW)]. Bulletin of KhNTUA 197:3-9, (in Ukrainian).

Gayda S.V. (2018): Дослідження та аналіз характеристик щитових конструкцій із вжи-ваної деревини / Doslidzhennya ta analiz kharakterystyk shchytovykh konstruktsiy iz vzhyvanoyi derevyny [A investigation and analysis of characteristics of solid furniture boards made of post-consumer wood]. Forestry, Forest, Paper and Woodworking Industry 44:15-25, (in Ukrainian). doi: https://doi.org/10.36930/42184402

Gayda S.V. (2023). Determination of the circularity indicator in the forest sector according to the principles of the circular economy. Forestry, Forest, Paper and Woodworking Indus-try, 49, 99-114. https://doi.org/10.36930/42234908 (in Ukrainian).

Gayda S.V. (2020) : Аналіз конструкцій та технологій виготовлення сучасних меблевих фасадів / Analiz konstruktsiy ta tekhnolohiy vyhotovlennya suchasnykh meblevykh fasadiv [Analysis of structures and technologies of manufacture of modern furniture facades]. Forestry, Forest, Paper and Woodworking Industry 46:54-64, (in Ukrainian). doi: https://doi.org/10.36930/42204606

Gayda S.V. (2023). State and analysis of the dynamics indicators of the production volume of the woodworking and furniture industry. Forestry, Forest, Paper and Woodworking Industry 49: 4-19 (in Ukrainian). doi: https://doi.org/10.36930/42234901

Gayda, S.V. (2015). Investigation of physical and mechanical properties of post-consumer wood (PCW). Actual problems of forest complex 43:175-179 (in Russian).

Gayda S.V., Ilkiv M.M., Savka D.B. (2021) : Дослідження технологічних процесів виго-товлення меблевих фасадів з масивної деревини // Doslidzhennya tekhnolohichnykh protsesiv vyhotovlennya meblevykh fasadiv z masyvnoyi derevyny. [Research of technological processes of manufacture of meble facades from solid wood]. Forestry, Forest, Paper and Woodworking Industry 47:22-33, (in Ukrainian). doi: https://doi.org/10.36930/42214703

Gayda S.V., Kiyko O.A. (2021): Властивості вживаної деревини як визначальний чин-ник якості меблевих виробів / Vlastyvosti vzhyvanoyi derevyny yak vyznachalʹnyy chynnyk yakosti meblevykh vyrobiv [Properties of used wood as a determining factor in the quality of furniture prod-ucts]. Scientific Works of the Forestry Academy of Sciences of Ukraine 23:152-162, (in Ukrainian). https://doi.org/10.15421/412135

Orikhovskyy R.Ya., Gayda S.V. (2020). The influence of different parameters of stability of production sites on the efficiency of functioning of woodworking production. Forestry, Forest, Paper and Woodworking Industry 46:49-53 (in Ukrainian). doi: https://doi.org/10.36930/42204605

Gayda S.V., Lesiv L.E. (2019): Визначення та порівняння властивостей вживаної дере-вини основних хвойних порід / Vyznachennya ta porivnyannya vlastyvostey vzhyvanoyi derevyny osnovnykh khvoynykh porid [A determination and comparison of properties of post-consumer wood of the basic conifers]. Forestry, Forest, Paper and Woodworking Industry 45:39-46, (in Ukrainian). doi: https://doi.org/10.36930/42194506

Gayda S.V. (2003). Гнучкі виробничі модулі для виготовлення ґратчастих меблевих ви-робів [Flexible production modules for the production of lattice furniture products]. Scientific Bulletin of UNFU 13.2:120-122. (in Ukrainian).

Gayda S.V., Petrishak I.V., Somar G.V. (2020): Дослідження впливу породи та режимів шліфування на питому продуктивність шліфувальної шкурки / Doslidzhennya vplyvu porody ta rezhymiv shlifuvannya na pytomu produktyvnistʹ shlifuvalʹnoyi shkurky [Study of the influence of breed and grinding modes on the specific productivity of grinding skin]. Forestry, Forest, Paper and Woodworking Industry 46:5-15, (in Ukrainian). doi: https://doi.org/10.36930/42204601

Gayda S.V., Salapak L.V., Lesiv L.E. (2021). Vyznachennya efektyvnoho tekhnolohichnoho protsesu vyhotovlennya riznykh opornykh elementiv dlya funktsionalʹnykh ploshchyn. [Determination of an efficient technological process of manufacturing various support elements for functional sur-faces]. Forestry, Forest, Paper and Woodworking Industry 47: 58-72, (in Ukrainian). doi: https://doi.org/10.36930/42214708

Gayda S.V., Somar G.V., Sokolovskyy I.A. (2022). Хімічна природа забруднювачів як основа класифікації виробів з деревини, що підлягають утилізації / Khimichna pryroda za-brudnyuvachiv yak osnova klasyfikatsiyi vyrobiv z derevyny, shcho pidlyahayutʹ utylizatsiyi [The chemical nature of pollutants as a basis for the classification of wood products to be utilization] . Forestry, Forest, Paper and Woodworking Industry 48:13-26, (in Ukrainian). doi: https://doi.org/10.36930/42214802

Gayda S.V., Voronovich V.V. (2011): Issledovanie osobennostey gnut'ya vtorichno ispol'zuemoy drevesiny [Investigation of the features of bending of post-consumer wood]. Scientific progress – creative young: proceedings of the International Scientific Conference, Mari State Uni-versity: 190-192, (in Russian).

Gayda S.V., Bilyy Ya.M. (2019). Дослідження технологічних процесів виготовлення ліжок двоспальних різних конструкцій / Doslidzhennya tekhnolohichnykh protsesiv vyhotovlennya lizhok dvospalʹnykh riznykh konstruktsiy [A investigation of technological processes of making beds of double different designs]. Forestry, Forest, Paper and Woodworking Industry 45:21-31 (in Ukrain-ian). doi: https://doi.org/10.36930/42194504

Gayda S.V., Voytovych I.G. (2017): Дослідження міцності та стійкості елементів ґрат-частих меблевих виробів із вживаної деревини / Doslidzhennya mitsnosti ta stiykosti elementiv gratchastykh meblevykh vyrobiv iz vzhyvanoyi derevyny [Durability and stability of elements for beam furniture products made from post-consumer wood are investigated]. Bulletin of KhNTUA 189:62-70, (in Ukrainian).

Gayda S.V., Voytovych I.G., Orikhovskyy R.Ya. (2020) : Дослідження технологічних процесів виготовлення ніжок столів обідніх різних конструкцій / Doslidzhennya tekhnolohichnykh protsesiv vyhotovlennya nizhok stoliv obidnikh riznykh konstruktsiy [Research of technological processes of production of legs of tables of various designs]. Forestry, Forest, Paper and Woodworking Industry 46:36-49, (in Ukrainian). doi: https://doi.org/10.36930/42204604

Gayda, S., Kiyko, O. (2020): The investigation of properties of blockboards made of post-consumer wood. Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements, 63(206), 77-102. https://doi.org/10.12841/wood.1644-3985.352.10

Gayda, S., Kiyko, O. (2023): Study of Physical and Mechanical Properties of Post-Consumer Wood of Different Age. Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements, 66(212), doi: https://doi.org/10.53502/wood-177453

Gayda, S.V., Kiyko O.A., Guz M.M. (2022): Research of the structure of stump and root-wood for effective use in the production of wood products. Folia Forestalia Polonica, Series A – For-estry, 64 (3):131-142, doi: https://doi.org/10.2478/ffp-2022-0011

Gayda, S.V., Kiyko, O.A. (2020): Determining the regime parameters for the surface cleaning of post-consumer wood by a needle milling tool. Eastern-European Journal of Enterprise Technologies, 5 [1 [107]], 89–97. doi: https://doi.org/10.15587/1729-4061.2020.212484.

Grytsak S.A., Gayda S.V. (2020): Порівняльний аналіз фізико-механічних характерис-тик гнутих елементів із різних порід дерев / Porivnyalʹnyy analiz fizyko-mekhanichnykh kharakterystyk hnutykh elementiv iz riznykh porid derev [Comparative analysis of physical and mechanical characteristics of bent elements from different tree species]. Forestry, Forest, Paper and Woodworking Industry 46:16-27, (in Ukrainian). doi: https://doi.org/10.36930/42204602

Voytovych I.G. (2010): Osnovy tekhnolohiyi vyrobiv z derevyny [Fundamentals of wood products technology]. – Lviv: Country of Angels, 305 p., (in Ukrainian).