Determination of the influence of rock and grinding modes on the surface roughness of wood

S.V. Gayda; I.V. Petryshak; Zh.Ya. Humeniuk

doi:10.36930/42214701

Authors

S.V. Gayda
I.V. Petryshak
Zh.Ya. Humeniuk

DOI:

https://doi.org/10.36930/42214701

Keywords:

technology, roughness, grinding, oak, spruce, cutting speed, pressing force, feed speed.

Abstract

Experimental studies of the influence of wood species and grinding modes on the roughness of the obtained surface were carried out. It is investigated that the type of wood also affects the magnitude of the irregularities of the surface to be treated, namely the magnitude of the roughness of the treated surface is inversely proportional to the density of the treated material. Regression models are obtained, which characterize the roughness of the surface of oak and spruce wood depending on the cutting speed and the specific pressure of pressing. It is established that the cutting speed has a positive effect on the roughness of the treated surface. This is due to the fact that at high cutting speeds wood fibers (especially relevant for hardwoods with higher density) show proper support to the cutter and do not have time to break under its pressure, and cut with a cutter before it breaks their connection with neighboring fibers. Therefore, the purity of the treated surface will be better. It is established that with the increase of cutting speed from 10 to 30 m / s by grinding skin of oak wood surface roughness decreases by 40-60%, and spruce - by 44-86%. Spruce has a 10-20% roughness dynamics than oak. It was found that with the increase of the specific pressure of pressing the part to the sanding skin on the surface of oak wood, the surface roughness increases by 20-30%, and the surface of spruce wood - by 12-32%. In spruce, the deterioration of roughness is 12-13% greater than in oak. It is established that with the increase of the feed rate on the surface of oak wood the surface roughness increases by 21-30%, in spruce - by 13.63-23.46%. In spruce deterioration of roughness by 9-13% more than in oak. To carry out effective grinding to obtain a quality surface (such as oak and spruce), the following input values are recommended: cutting speed 20-30 m / s; feed speed 6-8 m / min; specific clamping force 2.2-4.4 kPa; grain size of skins: P180-P150; P120-P100; P90-P60.

References

Berenice A.A. (1977): Issledovanye protsessa bestsentrovoho shlyfovanyya kruhlykh derevyannykh detaley. [Study of the process of centerless grinding of round wooden parts]. Abstract PhD. - Lviv. - 25 p. (in Russian)

Bugaenko Ya.P. (2010): Do pytannya profilʹnoho shlifuvannya derevyny [On the issue of profile sanding of wood]. Forestry, Forest, Paper and Woodworking Industry 36:100-102 (in Ukrainian).

Buglay B.M. (1957): Issledovanye y normalyzatsyya chystoty poverkhnosty drevesyny [Investigation and normalization of wood surface cleanliness]. Abstract of the doctor of technical sciences. Moscow, 36 p. (in Russian)

Gayda, S.V., Kiyko O.A. (2020): Determining the regime parameters for the surface cleaning of post-consumer wood by a needle milling tool. Eastern-European Journal of Enterprise Technologies, 5 [1 [107]], 89–97. doi: https://doi.org/10.15587/1729-4061.2020.212484.

Gayda, S.V., Kiyko O.A. (2020): The investigation of properties of blockboards made of post-consumer wood. Poznan : Drewno, 63 [206], 77-102. doi: https://doi.org/10.12841/wood.1644-3985.352.10.

Gayda S.V. (2011): Вживана деревина – додатковий ресурс сировини / Vzhyvana derevyna – dodat-kovyy resurs syrovyny [Recovered wood is additional resource of raw material]. Forestry, Forest, Paper and Woodworking Industry 37(1): 238-244 (in Ukrainian).

Gayda, S.V., Maksymiv, V.M. (2007): Аналіз, особливості, проблеми та досвід використання додаткових ресурсів сировини – відходів та вживаної деревини / Analiz, osoblyvosti, problemy ta dosvid vykorystannya dodatkovykh resursiv syrovyny – vidkhodiv ta vzhyvanoyi derevyny [Analysis, features, problems and experience of the use of additional resources of raw material – wastes and of used wood]. Forestry, Forest, Paper and Woodworking Industry 33:63-73 (in Ukrainian).

Gayda, S.V. (2007): Проблема деревної сировини у Європі та Україні / Problema derevnoyi syrovyny u Yevropi ta Ukrayini [А problem of arboreal raw material is in Europe and Ukraine]. Forestry, Forest, Paper and Woodworking Industry 33:55-63 (in Ukrainian).

Gayda S.V. (2013): Основи формування класифікатора вторинних деревинних ресурсів / Osnovy formuvannya klasyfikatora vtorynnykh derevynnykh resursiv [Bases of secondary wood resources classifier for-mation]. Scientific Works of the Forestry Academy of Sciences of Ukraine 11:208-215 (in Ukrainian).

Gayda S.V. (2017): Комплексні дослідження зміни пружних властивостей вживаної деревини ялиці з віком / Kompleksni doslidzhennya zminy pruzhnykh vlastyvostey vzhyvanoyi derevyny yalytsi z vikom [The complex studies on the change of elastic properties of post-consumer fir wood with age]. Forestry, Forest, Paper and Woodworking Industry 43:58-72 (in Ukrainian). doi: https://doi.org/10.36930/42174308

Gayda S.V. (2016): Ekologo-tekhnologicheskiye aspekty pererabotki vtorichno ispol'zuyemoy drevesiny dlya proizvodstva pressovannykh materialov [Ecological and technological aspects of recycling post-consumer wood for production compacted materials]. Lesnoy vestnik / Forestry bulletin of MSFU 20(3):15-22 (in Rus-sian).

Gayda S.V. (2016): Технологічні підходи до поверхневого очищення вживаної деревини голко-фрезерним інструментом / Tekhnolohichni pidkhody do poverkhnevoho ochyshchennya vzhyvanoyi derevyny holkofrezernym instrumentom [Technological approaches to cleaning of surface of post-consumer wood of needle-milling tools]. Bulletin of KhNTUA 178:3-11 (in Ukrainian).

Gayda S.V. (2015): Tekhnologії і fіziko-mekhanіchnі vlastivostі stolyarnikh plit іz vzhivanoї derevini [Technology and physical and mechanical properties blockboard made of post-consumer wood]. Technical ser-vice of agriculture, forestry and transport systems 3(1):145-152 (in Ukrainian).

Gayda S.V., Petryshak I.V., Somar G.V. (2020) : Дослідження впливу породи та режимів шлі-фування на питому продуктивність шліфувальної шкурки / Doslidzhennya vplyvu porody ta rezhymiv shlifuvannya na pytomu produktyvnistʹ shlifuvalʹnoyi shkurky [Study of the influence of breed and grinding modes on the specific productivity of grinding skin]. Forestry, Forest, Paper and Woodworking Industry 46:5-15 (in Ukrainian). doi: https://doi.org/10.36930/42204601

Kiyko O.A. (1994): Novyy instrument dlya chystovoho shlifuvannya derevyny [A new tool for fine sanding of wood] // Scientific Bulletin of UNFU 1:91-94 (in Ukrainian)

Kiyko O.A. (1995): Vplyv shvydkosti rizannya, shvydkosti podachi ta velychyny prytyskannya na sylovi pokaznyky protsesu shlifuvannya kombinovanymy zhorstko-pruzhnymy abrazyvnymy kruhamy [Influence of cutting speed, feed rate and pressure on the force indicators of the grinding process by combined rigid-elastic abrasive wheels] // Bulletin of UNFU 3(1):143-145 (in Ukrainian)

Kiyko O.A. (1999): Deyaki konstruktyvni osoblyvosti elastychnykh abrazyvnykh instrumentiv dlya shlifuvannya derevyny [Some design features of elastic abrasive tools for sanding wood] // Scientific Bulletin of UNFU 9(5):165-168 (in Ukrainian)

Petryshak I.V. (2003): Vyznachennya konstruktyvnykh parametriv zhorstko-pruzhnoho abrazyvnoho instrumenta [Determination of design parameters of rigid-elastic abrasive tool] // Scientific Bulletin of UNFU 13(1):137-142 (in Ukrainian)

Petryshak I.V. (2006): Obgruntuvannya strukturnykh parametriv zhorstkopruzhnoho abrazyvnoho instrumenta [Substantiation of structural parameters of rigid abrasive tool] // Nauk. Bulletin: Coll. scientific and technical work. - Lviv: NLTU of Ukraine. - 2006, issue. 16.3. - P. 70-75.

Petryshak I.V. (2003): Doslidzhennya rezhymnykh parametriv protsesu shlifuvannya derevyny buka zhorstko-pruzhnymy abrazyvnymy instrumentamy [Investigation of regime parameters of beech wood grinding process by rigid-elastic abrasive tools] // Scientific Bulletin of UNFU 13(2):133-136 (in Ukrainian)

Pyzhuryn A.A. (1984): Issledovanye protsessov derevoobrabotky [Research of woodworking processes]. Moscow: Forest Industry, 232 p. (in Russian)

Popov Yu.P. (1964): Issledovanye rabotosposobnosty shlyfovalʹnoy shkurky [Study of the efficiency of the grinding skin]. Abstract of PhD. Moscow, 23 p. (in Russian)

Rudakov B.N. (1940): Issledovanyya kachestva shlyfovannoy poverkhnosty drevesyny [Research of quality of the polished surface of wood]. Abstract of PhD. Moscow, 20 p. (in Russian).

Gayda S.V., Kshyvetskyy B.Ya., Voytovych I.G., Prokopovych B.V. (2002): Тлумачний словник з деревооброблення / Tlumachnyy slovnyk z derevoobroblennya [Explanatory dictionary from Woodworking]. Lviv: UNFU. – 280 p. (in Ukrainian)

Gayda S.V., Grytsak S.A. (2020) : Porivnyalʹnyy analiz fizyko-mekhanichnykh kharakterystyk hnutykh elementiv iz riznykh porid derev [Comparative analysis of physical and mechanical characteristics of bent elements from different tree species]. Forestry, Forest, Paper and Woodworking Industry 46: 16-27 (in Ukrainian). doi: https://doi.org/10.36930/42204602

Gayda S.V. (2017). Using fuzzy expert systems for decision support in the process of post-consumer wood sorting. Forestry, Forest, Paper and Woodworking Industry, 43, 5-20. https://doi.org/10.36930/42174301 (in Ukrainian).

Gayda S.V. (2020) : Analiz konstruktsiy ta tekhnolohiy vyhotovlennya suchasnykh meblevykh fasadiv [Analysis of structures and technologies of manufacture of modern furniture facades]. Forestry, Forest, Paper and Woodworking Industry 46:54-64 (in Ukrainian). doi: https://doi.org/10.36930/42204606

Gayda S.V. (2011). Recycled of post-consumer wood is for the production of particleboard in Ukraine / Proceedings of the XXI International symposium Adhesives in Woodworking Industry (Slovakia, Zvolen Juve 29 – July 01. 2011). TU Zvolen. – P. 108-121.

Gayda S.V. (2013). Techniques for utilization of post-consumer wood in the production of fuel pellets and briquettes. Proceedings of the XXI International symposium Adhesives in Woodworking Industry (Slo-vakia, Zvolen Juve 23-26. 2013). TU Zvolen, 119-130.

Gayda S.V. (2013). Розроблення технології виробництва паливних гранул на основі енергетично-го потенціалу вживаної деревини [Development of technology for the production of fuel pellets based on the energy potential of used wood]. Scientific Bulletin of UNFU 23.14:83-93. (in Ukrainian).

Gayda S.V. (2014). Teoreticheskoye obosnovaniye podkhoda po prognozirovaniyu prochnosti drevesnostruzhechnykh plit iz vtorichno ispol'zuyemoy drevesiny [The theoretical rationale for the approach on the prediction the strength of particleboard from recycled wood]. Actual problems of forest complex 38:212-216 (in Russian).

Gayda S.V., Kiyko O.A. (2018). Shape stability as a quality criterion for PCW-made blockboards. Pro-ceedings of the Forestry Academy of Sciences of Ukraine, 17, 185-192. https://doi.org/10.15421/411834 (in Ukrainian)

Gayda S.V. (2015). Modeling properties of blockboards made of post-consumer wood on the basis of the finite element method. Forestry, Forest, Paper and Woodworking Industry, 41, 39-49. https://doi.org/10.36930/42154106

Gayda S.V. (2016). Research on physical and mechanical characteristics of front blockboards made from post-consumer wood [Дослідження фізико-механічних характеристик фасадних столярних плит із вживаної деревини]. Forestry, Forest, Paper and Woodworking Industry 42: 33-50.

Gayda S.V. (2016). Технологічні підходи до поверхневого очищення вживаної деревини голкофре-зерним інструментом / Tekhnolohichni pidkhody do poverkhnevoho ochyshchennya vzhyvanoyi derevyny hol-kofrezernym instrumentom [Technological approaches to cleaning of surface of post-consumer wood of needle-milling tools]. Bulletin of KhNTUA 178:3-11(in Ukrainian).

Gayda S.V. (2017). Tekhnologiya i svoystva mebel'nogo shchita iz vtorichno ispol'zuemoy drevesiny [A technology and properties of furniture board made of post-consumer wood]. Actual problems of forest complex 48:34-38, (in Russian).

Gayda S.V. (2013). Resource-saving technologies of recycling of post-consumer wood]. Scien-tific Bulletin of NULES of Ukraine: Technology and Energy of agroindustrial complex 185(2):271-280, (in Ukrainian).

Gayda S.V. (2018). Технологія МДФ-фасадів / Tekhnolohiyi MDF-Fasadiv [MDF Facade Technolo-gies]. Forestry, Forest, Paper and Woodworking Industry 44:70-83 (in Ukrainian). doi: https://doi.org/10.36930/42184410

Gayda S.V. (2019). Scientific and technical basis of the use of used wood in woodworking: thesis of the Doctor of Technical Sciences in the specialty 05.23. – Lviv: UNFU. – 465 (in Ukrainian).

Gayda S.V., & Bilyy, Ya.M. (2016). The investigation of the shape stability of glued panels made of post-consumer wood. Forestry, Forest, Paper and Woodworking Industry, 42, 69-79. https://doi.org/10.36930/42164211 (in Ukrainian).

Gayda S.V., Kiyko O.A. (2021). Властивості вживаної деревини як визначальний чинник якості меблевих виробів / Vlastyvosti vzhyvanoyi derevyny yak vyznachalʹnyy chynnyk yakosti meblevykh vyrobiv [Properties of used wood as a determining factor in the quality of furniture products]. Scientific Works of the Forestry Academy of Sciences of Ukraine 23:152-162, (in Ukrainian). https://doi.org/10.15421/412135

Gayda S.V., Voytovych I.G. (2017). Durability and stability of elements for beam furniture products made from post-consumer wood are investigated. Bulletin of KhNTUA, 189, 62-70 (in Ukrainian).