Research of the influence of quantitative content and type of hardener on the properties of water-emulsion varnishes of domestic production
DOI:
https://doi.org/10.36930/42204609Keywords:
polyurethane, isocyanate, emulsion, varnish, hardener, hardness, viscosity, viability, protective and decorative coating.Abstract
In recent years, water-soluble, water-emulsion and other relatively environmentally friendly materials have become widespread. In the manufacture of products in enterprises, the consumer is less interested in the type of finishing material, but there is a direction associated with the finishing processes that directly affect the final consumer. This direction is the equipment of wooden floor coverings. Since most of these floor coverings are installed without finishing, they need further finishing directly on the installation site. Therefore, in order to reduce the negative impact on the health of the consumer, finishing works are carried out with acrylic, acrylic-polyurethane or polyurethane water-emulsion materials. Since the coatings formed by acrylic emulsions have low resistance to abrasion and water, they are mostly used for the manufacture of primers. Polyurethane or polyurethane-acrylic emulsions are used to make high-quality varnishes. It should be noted that in order to ensure high performance indicators, preference is given to two-component compositions which include a varnish-base and an isocyanate hardener. Most of the raw materials for manufacturing of two-component water-emulsion polyurethane varnishes are imported and quite expensive. Therefore, the urgent task is to establish the optimal ratio between its components. This is necessary to obtain cost-effective materials that will form h
In recent years, water-soluble, water-emulsion and other relatively environmentally friendly materials have become widespread. In the manufacture of products in enterprises, the consumer is less interested in the type of finishing material, but there is a direction associated with the finishing processes that directly affect the final consumer. This direction is the equipment of wooden floor coverings. Since most of these floor coverings are installed without finishing, they need further finishing directly on the installation site. Therefore, in order to reduce the negative impact on the health of the consumer, finishing works are carried out with acrylic, acrylic-polyurethane or polyurethane water-emulsion materials. Since the coatings formed by acrylic emulsions have low resistance to abrasion and water, they are mostly used for the manufacture of primers. Polyurethane or polyurethane-acrylic emulsions are used to make high-quality varnishes. It should be noted that in order to ensure high performance indicators, preference is given to two-component compositions which include a varnish-base and an isocyanate hardener. Most of the raw materials for manufacturing of two-component water-emulsion polyurethane varnishes are imported and quite expensive. Therefore, the urgent task is to establish the optimal ratio between its components. This is necessary to obtain cost-effective materials that will form high-quality coatings. So, this paper presents the results of the first stage of research on the properties of two-component water-emulsion polyurethane varnishes, which are being developed by one of the Ukrainian enterprise. The results of research of hardness of the protective and decorative coverings formed by varnishes on the basis of polyurethane emulsions with addition of isocyanate hardeners are resulted. The dependence of technological parameters of varnish application on the type and quantitative content of isocyanate hardener is described.
igh-quality coatings. So, this paper presents the results of the first stage of research on the properties of two-component water-emulsion polyurethane varnishes, which are being developed by one of the Ukrainian enterprise. The results of research of hardness of the protective and decorative coverings formed by varnishes on the basis of polyurethane emulsions with addition of isocyanate hardeners are resulted. The dependence of technological parameters of varnish application on the type and quantitative content of isocyanate hardener is described.
References
Gayda S.V. (1998). Основи створення гнучких автоматизованих виробництв [Basics of creating flexible automated production]. – Lviv. – 149 p. (in Ukrainian).
Gayda S.V. (1999). Проблеми та перспективи роботизації меблевої промисловості [Problems and prospects of robotics in the furniture industry]. Scientific Bulletin of UNFU 9.5:192-195. (in Ukrainian).
Gayda S.V. (2000). Визначення стійкості та міцності вертикальних стінок корпусних меблевих ви-робів [Determination of stability and strength of vertical walls of case furniture products]. Scientific Bulletin of UNFU 10.3:127-129. (in Ukrainian).
Gayda S.V. (2000). Матеріали для виготовлення виробів з деревини / Materialy dlya vyhotovlennya vyrobiv z derevyny / Materials for the Productsion of wood Productss. – Lviv: BMC. – 160 p., (in Ukrainian).
Gayda S.V. (2000). Особливості розрахунку корпусних виробів на міцність [Peculiarities of strength calculation of hull products]. Scientific Bulletin of UNFU 10.2:150-154. (in Ukrainian).
Gayda S.V. (2001). Раціональне конструювання виробів з деревини / Ratsionalʹne konstruyuvannya vyrobiv z derevyny [Rational constructing of wood Productss]. Lviv: BMC. – 93 p., (in Ukrainian).
Gayda S.V. (2002). Особливості та перспективи роботизації меблевої промисловості України [Peculiarities and prospects of robotization of the furniture industry of Ukraine]. Scientific Bulletin of UNFU 12.5:38-40. (in Ukrainian).
Gayda S.V. (2003). Гнучкі виробничі модулі для виготовлення ґратчастих меблевих виробів [Flexible production modules for the production of lattice furniture products]. Scientific Bulletin of UNFU 13.2:120-122. (in Ukrainian).
Gayda S.V. (2004). Інтегровані технології меблевого виробництва [Integrated technologies of furni-ture production]. Scientific Bulletin of UNFU 14.4:118-121. (in Ukrainian).
Gayda S.V. (2007). Дослідження концентрації операцій у сучасному меблевому виробництві / Doslidzhennya kontsentratsiyi operatsiy u suchasnomu meblevomu vyrobnytstvi [Research of concentration of operations is in modern furniture Productsion]. Forestry, Forest, Paper and Woodworking Industry 33:73-79 (in Ukrainian).
Gayda S.V. (2013). The technological solutions for recycling of post-consumer wood. Proceedings of I International Interdisciplinary Scientific Conference Formation of stable outlook as the basis of sustainable development (Ukraine, Lviv, 14-16 March 2013) UNFU: Lviv, 5-11.
Gayda S.V. (2013). Розроблення технології виробництва паливних гранул на основі енергетично-го потенціалу вживаної деревини [Development of technology for the production of fuel pellets based on the energy potential of used wood]. Scientific Bulletin of UNFU 23.14:83-93. (in Ukrainian).
Gayda S.V. (2014). Sposoby podgotovki k pererabotke vtorichno ispol'zuyemoy drevesiny iglofrezerny-mi i shchotochnymi stankami [Preparation methods for processing of post-consumer wood (PCW) needle-milling and brushing machines]. Actual problems of forest complex 40:65-69 (in Russian).
Gayda S.V. (2015). Investigation of physical and mechanical properties of post-consumer wood. Ac-tual problems of forest complex 43:175-179, (in Russian).
Gayda S.V. (2015). Tekhnologії і fіziko-mekhanіchnі vlastivostі stolyarnikh plit іz vzhivanoї derevini [Technology and physical and mechanical properties blockboard made of post-consumer wood]. Technical ser-vice of agriculture, forestry and transport systems 3(1).145-152 (in Ukrainian).
Gayda S.V. (2016). Formoustoychivost' stolyarnykh plit iz vtorichno ispol'zuemoy drevesin [A form of stability of blockboards made of post-consumer wood]. Actual problems of forest complex 46:148-153, (in Russian).
Gayda S.V. (2017). Tekhnologiya i svoystva mebel'nogo shchita iz vtorichno ispol'zuemoy drevesiny [A technology and properties of furniture board made of post-consumer wood]. Actual problems of forest complex 48:34-38, (in Russian).
Gayda S.V. (2017). Використання нечітких експертних систем для підтримки прийняття рішень в процесі сортування вживаної деревини / Vykorystannya nechitkykh ekspertnykh system dlya pidtrymky pryynyattya rishenʹ v protsesi sortuvannya vzhyvanoyi derevyny [Using fuzzy expert systems for decision sup-port in the process of post-consumer wood sorting]. Forestry, Forest, Paper and Woodworking Industry 43:5-20 (in Ukrainian). doi: https://doi.org/10.36930/42174301
Gayda S.V. (2017). Комплексні дослідження зміни пружних властивостей вживаної деревини ялиці з віком / Kompleksni doslidzhennya zminy pruzhnykh vlastyvostey vzhyvanoyi derevyny yalytsi z vikom [The complex studies on the change of elastic properties of post-consumer fir wood with age]. Forestry, For-est, Paper and Woodworking Industry 43:58-72 (in Ukrainian). doi: https://doi.org/10.36930/42174308
Gayda S.V. (2018). A investigation and analysis of characteristics of solid furniture boards made of post-consumer wood. Forestry, Forest, Paper and Woodworking Industry, 44, 15-25. https://doi.org/10.36930/42184402 (in Ukrainian).
Gayda S.V. (2018). Strength of combined blockboard made of post-consumer wood (PCW). Bulletin of KhNTUA 197:3-9, (in Ukrainian).
Gayda S.V. (2018). Технологія МДФ-фасадів / Tekhnolohiyi MDF-Fasadiv [MDF Facade Technologies]. Forestry, Forest, Paper and Woodworking Industry 44:70-83 (in Ukrainian). doi: https://doi.org/10.36930/42184410
Gayda S.V. (2019). Scientific and technical basis of the use of used wood in woodworking: thesis of the Doctor of Technical Sciences in the specialty 05.23. – Lviv: UNFU. – 465 (in Ukrainian).
Gayda S.V., Bilyy Ya.M. (2019). Дослідження технологічних процесів виготовлення ліжок двос-пальних різних конструкцій / Doslidzhennya tekhnolohichnykh protsesiv vyhotovlennya lizhok dvospalʹnykh riznykh konstruktsiy [A investigation of technological processes of making beds of double different designs]. Forestry, Forest, Paper and Woodworking Industry 45:21-31 (in Ukrainian). doi: https://doi.org/10.36930/42194504
Gayda S.V., Kiyko O.A. (2013). Технология очистки вторично используемой древесины иглофре-зерными станками [The technology of cleaning recycled wood with needle milling machines] // Actual prob-lems and prospects of the development of LPK: materials II NTK., September 9-11, 2013 – Kostroma. – P. 36-39. (in Russian).
Gayda S.V., Kiyko O.A. (2018). Shape stability as a quality criterion for PCW-made blockboards. Proceedings of the Forestry Academy of Sciences of Ukraine, 17, 185-192. https://doi.org/10.15421/411834 (in Ukrainian)
Gayda S.V., Kiyko O.A. (2020). Determining the regime parameters for the surface cleaning of post-consumer wood by a needle milling tool. Eastern-European Journal of Enterprise Technologies, 5 (1(107)), 89-97. https://doi.org/10.15587/1729-4061.2020.212484.
Gayda S.V., Kiyko O.A. (2020). The investigation of properties of blockboards made of post-consumer wood. Poznan : Drewno, 63(206), 77-102. https://doi.org/10.12841/wood.1644-3985.352.10.
Gayda S.V., Kshyvetskyy B.Ya. (1999). Техніко-економічні характеристики деревообробної фаб-рики майбутнього [Technical and economic characteristics of the woodworking factory of the future]. Scientific Bulletin of UNFU 9.3:83-85. (in Ukrainian).
Gayda S.V., Kshyvetskyy B.Ya., Voytovych I.G., Prokopovych B.V. (2002). Тлумачний словник з деревооброблення / Tlumachnyy slovnyk z derevoobroblennya [Explanatory dictionary from Woodworking]. – Lviv: UNFU. – 280 p. (in Ukrainian).
Gayda S.V., Lesiv L.E. (2019). Визначення та порівняння властивостей вживаної деревини ос-новних хвойних порід / Vyznachennya ta porivnyannya vlastyvostey vzhyvanoyi derevyny osnovnykh khvoynykh porid [A determination and comparison of properties of post-consumer wood of the basic conifers]. Forestry, Forest, Paper and Woodworking Industry 45:39-46 (in Ukrainian). doi: https://doi.org/10.36930/42194506
Gayda S.V., Maksimiv V.M., Kiyko O.A., Ferenc O.B. (2013). Залишки деревини та деревина після споживання. Класифікація. Терміни та визначення [Wood residues and post-consumer wood. Classifi-cation. Terms and definitions] / Agreement No. 08.24-11-1: draft international standard ISO. – Lviv: NLTU of Ukraine – 53 p. (in Ukrainian).
Gayda S.V., Nikityuk L.O. (1998). До питання застосування екстрагованої деревини для плитного виробництв [On the issue of using extracted wood for slab production]. Scientific Bulletin of UNFU 8:75-77. (in Ukrainian).
Gayda S.V., Voronovich V.V. (2011). Investigation of the features of bending of post-consumer wood // Proceedings of the Conference, Mari State University. – 190-192 (in Russian).
GOST 5233-89. (1989). Материалы лакокрасочные. Метод определения твердости по маятнико-вому прибору [Paint materials. Method for determination of coating hardness with pendulum instrument]. – Moskow: Publishing house of standards. – 7 p., (in Russian).
GOST 8420-74. (1974). Материалы лакокрасочные. Методы определения условной вязкости / Materialy lakokrasochnyye. Metody opredeleniya uslovnoy vyazkosti [Paint and Lacquer Materials. Method for determination of relative viscosity]. – Moskow: Publishing house of standards. – 7 p., (in Russian).
Voytovych I.G. (2010). Основи технології виробів з деревини / Osnovy tekhnolohiyi vyrobiv z derevyny (Fundamentals of wood products technology). – Lviv: Country of Angels, 305 p. (in Ukrainian).
Офіційний сайт Alberdingk. [Alberdingk official site]. – Доступний з / Available at http://www.alberdingk-boley.de/.
Офіційний сайт Covestro. [Covestro official site]. – Доступний з / Available at https://solutions.covestro.com/.
Офіційний сайт Lamberti. [Lamberti official site]. – Доступний з / Available at http://www.lamberti.ru/.
Downloads
Published
Issue
Section
How to Cite
